Trending posts from Wranglerforum.com!

Hey guys, I have a '15 JKUR D44 front stock axle. I've had 3 axle leaks on the driver side front from the seals where I have diff fluid dripping on my hubs then onto my tires, ... [Wranglerforum.com Logo]  Hi {NAME}! Here's your weekly guide to trending discussions at Wranglerforum.com! Highlighted posts [Leaking axles after multiple warranty repairs, dealer refuses axle replacement. Advice?](  October 30, 2020  •  58 posts  •  1,123 views  [JK Tech Forum](   [BKJKU said]( — Hey guys, I have a '15 JKUR D44 front stock axle. I've had 3 axle leaks on the driver side front from the seals where I have diff fluid dripping on my hubs then onto my tires, ... [Read more »](  [Need Help, Frame suspension repair, first post](  October 30, 2020  •  30 posts  •  659 views  [TJ Tech Forum](   [Daveyjones617 said]( — Hi all, so I noticed my jeep was a bouncy yesterday & noticed pics below this morning! I could use some advice getting this fixed. I don't have the ability to weld myself. This ... [Read more »](  [New pressure plate surface not smooth?](  October 31, 2020  •  13 posts  •  344 views  [YJ Tech Forum](   [WinterTurtle said]( — Every pressure plate I can recall having seen has been polished / flat finish. Here's my brand new LUK brand pp. Is this a thing or a missed machining process? [image] [Read more »](  [JKU on cocaine 😂](  October 30, 2020  •  22 posts  •  803 views  [JK Tech Forum](   [Alghobi said]( — As the title say lol...my JKU drives straight on clean highways without even touching the steering-wheel. As soon as I put my hands on, it feels that it need correction constantly ... [Read more »](  [You guys were right, I was wrong (rear track bar)](  November 01, 2020  •  8 posts  •  273 views  [YJ Tech Forum](   [Steve Beswick said]( — After owning my YJ since April or May I finally removed my rear track bar today. I'm not sure how, but it almost seems as though both axles ride better. I mean it's still rough, ... [Read more »](  [I'd like you to meet my friend Jack.](  October 30, 2020  •  18 posts  •  489 views  [General Jeep Discussion](   [Steve Beswick said]( — It's not everyday I get to buy some shiny new stuff that isn't technically a "need", so I thought I'd share the joy of my new acquisition! [image] [Read more »](  [2.5 yj won't go over 60mph.](  October 30, 2020  •  15 posts  •  429 views  [YJ Tech Forum](   [Lakeguy2302 said]( — I have a 95 th 2.5 5 speed. Just bought it a few weeks ago. Previoys owner put a 3 inch lft and 33's on it. My issue is that it will not go above 60 mph...at all. I know its not ... [Read more »](  [Bad reputation](  October 28, 2020  •  37 posts  •  877 views  [TJ Tech Forum](   [Bbrayden85 said]( — So i just bought my first wrangler. It is a '97 2.5l and im having issues. I bought the truck a few days ago and i drove it home just fine. The day after i drove it to work and ... [Read more »](  [2006 TJ Wont Turn Over With Key and Odometer has all 8s](  November 01, 2020  •  13 posts  •  419 views  [TJ Tech Forum](   [Sslade8774 said]( — I recently picked up a 2006 TJ. I was told that it needed an ECM and hadn't run in 2 years. I have had the ECM rebuilt but the Jeep still reads all eights on the odometer. It will ... [Read more »](  [Is this a polit bearing ?](  October 31, 2020  •  12 posts  •  346 views  [TJ Tech Forum](   [Joejeep99 said]( — I have a 99 tj automatic. bought a 4.0 out of 97 tj Manuel. Keeping my jeep automatic. When i go to bolt the motor onto the trans the crank pulley wont turn. It turns fine when ... [Read more »](  You are receiving this email because you either registered as a member for Wranglerforum.com or signed up for updates.  [Unsubscribe](  [Send feedback](mailto:digest@threadloom.news?subject=Feedback%20for%20Wranglerforum.com%20newsletter)  Sent on behalf of Wranglerforum.com by  [Threadloom]( WranglerForum.com, VerticalScope Inc., 111 Peter St, Suite 901, Toronto, ON M5V 2H1